Korrekte Bedienung von konventionellem Fräsen und Steigfräsen

Milling plays a pivotal role in the manufacturing industry, shaping countless products and components we use daily. Especially when precision is paramount, understanding the nuances between different milling techniques becomes crucial. One such distinction lies between conventional milling (or up milling) and climb milling (or down milling).

Definitions of Conventional and Climb Milling

In the realm of milling operations, the rotation direction of the milling cutter typically remains constant. However, the direction of feed can vary. This has led to the emergence of two prevalent milling techniques: conventional milling (also known as up milling) and climb milling (often referred to as down milling).

Conventional Milling (Up Milling)

Conventional milling is when the milling cutter spins in the same direction as the workpiece moves. In simpler terms, the cutter rotates against the direction of the feed.

Climb Milling (Down Milling)

On the other hand, in climb milling, the milling cutter spins in the opposite direction to the way the workpiece is moving. This means the cutter rotates in the same direction as the feed.

Anmerkung: It’s essential to understand that the determination of whether an operation is conventional or climb milling is based on the feed direction of the workpiece, not the feed direction of the cutter.

Practical Identification Methods

When milling the outer contour of a workpiece (assuming the cutter rotates clockwise):

• If the feed direction is clockwise along the workpiece’s outer contour, it’s conventional milling.
• If the feed direction is counter-clockwise along the workpiece’s outer contour, it’s climb milling.

On the other hand, when milling the inner contour of a workpiece (again, assuming the cutter rotates clockwise):

• If the feed direction is counter-clockwise along the workpiece’s inner contour, it’s conventional milling.
• If the feed direction is clockwise along the workpiece’s inner contour, it’s climb milling.

Characteristics of Conventional and Climb Milling

Milling operations, whether conventional or climb, come with their unique set of advantages and challenges. Understanding these characteristics can help manufacturers make informed decisions about which method to employ for a specific task.

Features of Conventional Milling (Up Milling)

In conventional milling, the thickness of the chip decreases progressively from the start of the cut until it reaches zero by the end of the cut. This absence of friction prevents the cutting edge from scraping and rubbing against the surface of the part before the actual cut begins. Moreover, because the chips move from thick to thin during conventional milling, it’s less likely to form burrs when machining ductile materials.

As illustrated in the provided image:

• The vertical force (FV) exerts downward pressure on the workpiece, aiding in its secure clamping.
• The horizontal force (FH) moves in the same direction as the workpiece’s feed. This can be disadvantageous as it doesn’t help in eliminating the gap in the machine table’s lead screw. When the force exerted by the cutter teeth on the workpiece is significant, it can lead to chatter, compromising the smoothness of the cut.

Features of Climb Milling (Down Milling)

In climb milling, the chip thickness starts from zero and gradually increases as the cutter tooth rotates until the end of the cut. The cutter tooth doesn’t immediately engage with the workpiece; instead, it skids on the already machined surface. This skidding can harden the surface, deteriorating its quality and accelerating the wear of the cutter tooth.

As depicted in the provided image:

• The vertical force (FV) has an upward-lifting effect on the workpiece. This upward force tends to pull the workpiece out of its clamp, which isn’t conducive to secure clamping.
• Conversely, the horizontal force (FH) moves in the opposite direction of the workpiece’s feed. This is beneficial as it helps eliminate the gap in the machine table’s lead screw, ensuring a steady feed and minimal vibration.

Milling Techniques for End Face Milling

End face milling, a crucial aspect of the machining process, can be approached in various ways depending on the relative position of the milling cutter to the workpiece. Understanding these techniques and their implications can help in achieving optimal results.

Symmetrical Milling

When the workpiece is positioned centrally to the milling cutter, the process is termed as symmetrical milling. In this method, the chip thickness remains consistent during both the entry and exit of the cut, resulting in a substantial average cutting thickness.

Asymmetrical Conventional Milling (Up Milling)

In this technique, the milling cutter is offset to one side of the workpiece’s symmetrical plane. As the cutter exits the material, the chip thickness is at its minimum. This method is particularly suitable for materials like stainless steel, which have a high deformation coefficient and are prone to work hardening.

Asymmetrical Climb Milling (Down Milling)

Here, the milling cutter is also offset to one side of the workpiece’s symmetrical plane. However, as the cutter enters the material, the chip thickness is minimal. This results in a smaller initial impact, consistent cutting force, and a smoother milling process. This technique is especially effective when machining carbon steel and high-strength low-alloy steel.

The Golden Rule of Milling: From Thick to Thin

A paramount consideration during milling is the formation of chips. The position of the milling cutter plays a decisive role in chip formation. It’s essential to ensure that a thick chip forms as the cutter edge enters the material and a thin chip as it exits. This “thick to thin” principle guarantees a stable milling process, ensuring that the chip thickness is as minimal as possible upon the cutter’s exit. This approach not only enhances the quality of the finished product but also prolongs the life of the milling tools.

Tips for Choosing Between Conventional and Climb Milling

Selecting the right milling technique is crucial for achieving the desired results. The choice between conventional milling (up milling) and climb milling (down milling) depends on various factors, including the material being machined and the specific challenges faced during the machining process.

Based on Material Characteristics

• Standard Machining Conditions: When the machine tool, fixture, and workpiece are allowed, conventional milling is often the preferred method. This is because it tends to enhance the lifespan of the milling cutter and improve the surface quality of the machined part.
• Presence of Surface Imperfections: If the workpiece surface has imperfections such as scale (black skin), hardened layers, or significant unevenness, climb milling is recommended. This is because, in climb milling, the cutter teeth engage the already machined surface, reducing the risk of tool chipping.
• Machining Difficult Materials (with a strong tendency to harden): For materials that are challenging to machine due to their hardening tendencies, conventional milling is advised. This method not only minimizes cutting deformation but also reduces cutting resistance.
• Machining High-Temperature Alloys with Ceramic Cutters: When using ceramic cutting tools to machine high-temperature alloys, climb milling is suggested. Ceramic tools are sensitive to the impact generated when entering the workpiece, making climb milling a more suitable choice.

Based on Machining Challenges

• Damage or Wear on the Back End of The Tool: If there’s noticeable wear on the trailing edge of the tool, it’s best to opt for conventional milling. This approach helps avoid issues like tool scraping and excessive wear caused by squeezing.
• Vibration Due to Tool Overhang: In precision machining, if there’s a significant tool overhang leading to vibrations, climb milling is the way to go.
• Vibration Due to Poor Spindle Rigidity: In situations where there’s a lack of spindle rigidity, especially during machining processes with high cutting resistance (like shoulder milling), trying climb milling can be beneficial.

Mastery in Milling: Prototool’s Commitment to Excellence

Conventional milling and climb milling are foundational techniques in the milling process. For a distinguished manufacturing service provider, mastering these methods is non-negotiable. At Prototool, we not only understand the intricacies of these techniques but excel in their application. Drawing from our vast experience and expertise, we ensure that every project we undertake is a testament to our commitment to precision and quality. When you choose Prototool, you’re choosing a partner who has made it their mission to master the very basics, ensuring that your designs are brought to life with unparalleled accuracy and finesse.